[8+] V Belt Size Table

V and Flat Belt Design and Engineering Data. AX Section Cogged 12.

Belt Drives And Chain Drives

45 PRODUCT DESCRIPTION METAL.

V belt size table. The dimensions of various sections of the V-belt are shown below. Dimensions of V-belts and pulleys together with basic design data are covered in this manual. Measure the internal length of the belt.

D Section Banded V-Belts. AP BP CP 5VP 8VP SPBP 12 516 2132 1332 78 1732 78 58 1 16mm 22mm 3564 13mm 18mm Super HC. Set the flat outer edge of the V belt on a flat surface.

This manual does not apply to automotive and agricultural drives. 42 optibelt VARIO POWER Variable Speed Belts. DIMENSIONS 61 Cross section V-belt shall have cross sectional dimensions as shown in Table 2.

Combine cross section plus Inside Circumference IC to determine belt part. X designates molded notch construction. Coded 50 is exactly 100 inches inside length.

Optibelt SUPER TX MS V-Belts Profiles ZXX10 AXX13 BXX17 CXX22. Standard and non-standard sections and lengths in imperial metric and high capacity range. Standard Groove Sheave Widths.

Internal length V belt width. V-belts also known as Vee belt or wedge rope are an early solution that solved the slippage and alignment problem. Width B Section 58.

And lengths from 16. Classical V-Belts for JIS K 6323 Table 1-1 M Belt indication M50 Cross Section Belt Codeinch 10 6. Width C Section 78.

B50 is a B section of 50 inches inside length. They usually transmit power from both sides of the belt. Figure 2 Cross Section of V-Belt 310.

Width BX Section Cogged 58. General cross sectional dimensions that are used in the US are shown below. 2874 -- 3054 8 3054 -- 3234 13 3234 -- 3414 16 3414 -- 3594 14 3594 -- 3774 17 3774 -- 3954 18 more.

A B C D and E. C Section Banded V-Belts. 31082010 Example belt is 450.

To learn more about how you can help Engineers Edge remain a free resource and not see advertising or this message please visit Membership. B Section Banded V- Belts. Click here or Select V-belt catogory to purchase our High Quality Low Price Vbelts including sizes 3L 3V 3VX 5V5VX8VA AX B BX C CX.

Hex belts also known as double V-belts are designed for use on drives with one or more reverse bends. A 20 4L 220 A 21 4L 230 A 22 4L 240 A 23 4L 250 A 24 4L 260 A 25 4L 270 A 26 4L 280. V-belt is the rubber belt that drives things such as the alternator air conditioning compressor power steering pump and waterpump.

Standard v belts are manufactured from a special formulated rubber and reinforced high strength polyester cords for uniformity. V-Belts SPCP Aramid tensile cords provide superior service on high impact shock-loaded drives. V-belts run smoother and quieter last longer and substantially improve energy efficiency compared to noncogged belts.

Width E Section 1-12. CHART Single V-Belts Predator. Measure the width of the belt.

Width Classic V Belts. The general part number format is the cross section size and the inside length in inches eg. 5mm 6mm 65mm 8mm 10mm z13mm A 17mm B 22mm C 20mm and 25mm.

If the code is 49 then it is 999. The width ranges from 12. 4L to A Belt Conversion.

Nominal Dimensions of V-belt Cross Sections in mm Classical V-Belts 01 Cross Section W H α Features 125 165 220 315 A B C D. Outside Circumference mm 547 -- 6025 3. Width B Section 58.

Available size for Raw Edge Cogged V-Belts AX Belt indication A13 AX A64 Cross section Belt Codeinch 13 9 Standard Belt Sizes M-Section A-Section Belt Code Effective length Le mm Belt Code Pitch length Lp mm Belt Code Pitch length Lp mm Belt Code Pitch length Lp mm. Classic A Section V-Belt. V-Belt Pulley Sheave Sizes Table Chart.

And if the code is 51 then it is 1001. SPZ 10N SPA 13N SPB 16N SPC 22N 19mm. The question of matched sets arises in case of multi V-belt drive as the length of V-belt should be matched in order to obtain even distribution of load.

For instance a V-belt with size 100. However classical V-belts have high tolerance for poor operating conditions. The V-belt shall have a trapezoidal cross section with an endless loop and made out of material specified as above.

22022010 The V-Belts are basically classified into 5 types or sections ie. 43-44 optibelt DK Double-Sided V-Belts Profiles AAHAA BBHBB CCHCC DDHDD 22 x 22 25 x 22. V-Belts Combine cross section designation with Outside Circumference OC to the nearest whole number plus a zero to determine Belt Part Number.

These are used in many industries such as industrial agricultural material handling HVAC and much more. Double Angle V-Belts and Kraftbands. A 12 B 2132 c 78 D 1 14 E 1 12 Measuring Belt Length with an Old V Belt Place a mark on the side of an old V belt with a white paint marker.

Classic Banded V-Belts A B C D A Section Banded V-Belts. Classic V-Belts A B C D E 12 A Classic V-Belts 2132 B Classic V-Belts 78 C Classic V-Belts 1-14 D Classic V-Belts 1-12 E Classic V-Belts. Width C Section 78.

The V shape of the belt tracks in a mating groove in the pulley or sheave so that the belt cannot slip off. Put together the part number. Kevlar V-Belts 3L A4L B5L C.

The categorization of this is based on the cross sectional size of the belt and the amount of power to be transmitted by the belt. Width Classic Cogged V Belts. Width D Section 1-14.

The following table defiens industry standard V-Belt sheave grooves. Width A Section 12. Nominal dimensions of the four cross sections are given in Table 1.

Top width 5VX belt with 80.

V Belt Pulley Sheave Sizes Table Chart Engineers Edge